Texas Energy Comparison

Energy Saving Tips

Energy Performance Ratings

Appliances & Electronics
- Buying Efficient Products
- Estimating Energy Use
- Turning Off Computers

Electricity
- Reducing Electricity Use
- Buying Clean Electricity
- Making Clean Electricity
- Reading Electric Meters

Insulation & Air Sealing
- Weather-stripping & Caulking
- Insulation
- Controlling Moisture
- Ventilation

Lighting & Day Lighting
- Artificial Lighting
- Types of Lighting
- Turning Off Lights
- Natural Lighting

Windows, Doors & Skylights
- Energy Performance Ratings
- Selecting Windows
- Selecting Exterior Doors
- Selecting Skylights

Design & Remodeling
- Passive Solar
- Whole-House Design
- Zero-Energy Homes
- Log Homes
- Manufactured Homes
- Earth-Sheltered Homes
- Financing an Efficient Home

Heating & Cooling
- Selecting & Replacing Your System
- Cooling Systems
- Heating Systems
- Heat Pumps
- Thermostats, Ducts, & Meters

Landscaping
- For Your Climate
- For Your Microclimate
- Shading
- Using Windbreaks
- Conserving Water & Xeriscaping

Water Heating
- Selecting a Water Heater
- Solar Water Heaters
- Demand (Tankless) Water Heaters
- Reducing Water Heating Bills
- Swimming Pool Heating

Connect With Energy Savers
- Energy Savers Blog
- Facebook

Energy Performance Ratings for Windows, Doors, and Skylights
You can use the energy performance ratings of windows, doors, and skylights to tell you their potential for gaining and losing heat, as well as transmitting sunlight into your home.

Heat Gain and Loss
Windows, doors, skylights can gain and lose heat in the following ways:

• Direct conduction through the glass or glazing, frame, and/or door
• The radiation of heat into a house (typically from the sun) and out of a house from room-temperature objects, such as people, furniture, and interior walls
• Air leakage through and around them.
These properties can be measured and rated according to the following energy performance characteristics:

U-factor
The rate at which a window, door, or skylight conducts non-solar heat flow. It's usually expressed in units of Btu/hr-ft2-ºF. For windows, skylights, and glass doors, a U-factor may refer to just the glass or glazing alone. But National Fenestration Rating Council U-factor ratings represent the entire window performance, including frame and spacer material. The lower the U-factor, the more energy-efficient the window, door, or skylight.

• Solar heat gain coefficient (SHGC)
A fraction of solar radiation admitted through a window, door, or skylight—either transmitted directly and/or absorbed, and subsequently released as heat inside a home. The lower the SHGC, the less solar heat it transmits and the greater its shading ability. A product with a high SHGC rating is more effective at collecting solar heat gain during the winter. A product with a low SHGC rating is more effective at reducing cooling loads during the summer by blocking heat gained from the sun. Therefore, what SHGC you need for a window, door, or skylight should be determined by such factors as your climate, orientation, and external shading. For more information about SHGC and windows, see passive solar window design.

• Air leakage
The rate of air infiltration around a window, door, or skylight in the presence of a specific pressure difference across it. It's expressed in units of cubic feet per minute per square foot of frame area (cfm/ft2). A product with a low air leakage rating is tighter than one with a high air leakage rating.

Sunlight Transmittance
A window's, door's, or skylight's ability to transmit sunlight into a home can be measured and rated according to the following energy performance characteristics:

• Visible transmittance (VT)
A fraction of the visible spectrum of sunlight (380 to 720 nanometers), weighted by the sensitivity of the human eye, that is transmitted through a window's, door's, or skylight's glazing. A product with a higher VT transmits more visible light. VT is expressed as a number between 0 and 1. The VT you need for a window, door, or skylight should be determined by your home's daylighting requirements and/or whether you need to reduce interior glare in a space.

• Light-to-solar gain (LSG)
The ratio between the SHGC and VT. It provides a gauge of the relative efficiency of different glass or glazing types in transmitting daylight while blocking heat gains. The higher the number, the more light transmitted without adding excessive amounts of heat. This energy performance rating isn't always provided.

Energy Performance Testing, Certification and Labeling
The National Fenestration Rating Council (NFRC) operates a voluntary program that tests, certifies, and labels windows, doors, and skylights based on their energy performance ratings. The NFRC label provides a reliable way to determine a window's energy properties and to compare products.

The NFRC label can be found on all ENERGY STAR® qualified window, door, and skylight products, but ENERGY STAR bases its qualification only on U-factor and SHGC ratings.

See Learn More on the right side of this page (or below if you've printed it out) for links to NFRC and ENERGY STAR information.

Switch to a Renewable Energy Plan Now

www.GreenElectricRates.com

Texas Service Areas - Houston, TX - Dallas - Fort Worth - Arlington - Corpus Christi - Plano - Garland - Lubbock - Irving - Laredo - Pasadena - Brownsville - Grand Prairie - Mesquite, TX - Abilene - Beaumont - Waco - Carrollton - McAllen - Wichita Falls - Midland - Richardson - Odessa - San Angelo - Killeen - Tyler - Denton -Lewisville, TX - Longview - College Station - Baytown - Bryan - Sugar Land - Round Rock - Victoria - Harlingen - Galveston - The Woodlands, TX - North Richland Hills, TX - Temple - McKinney - Missouri - Flower Mound - Edinburg - Bedford - Pharr - Euless - League City - Mission - Rowlett - Allen - Grapevine - Texas City - Haltom City - DeSoto - Pearland - Conroe - Alice - Denison - Ft. Hood, TX - Odessa - Sherman - Links and more...